In case you’ve chosen the flawed channel map in Betaflight, your drone will reply to the flawed sticks, inflicting management points. It’s important to make sure the proper channel map is chosen within the Receiver tab in Betaflight. In case you’re bored with altering the channel map every time you arrange a brand new drone, I can even present you how you can configure channel order in your EdgeTX radio so that you gained’t want to alter it once more.
In search of a brand new radio? Listed below are my really helpful radio transmitters: https://oscarliang.com/radio-transmitter/#Radio-Suggestions
What’s Channel Map in Betaflight?
Channel mapping refers back to the order by which your radio’s controls (throttle, yaw, pitch, roll) are transmitted to your drone. Betaflight expects these controls in a selected order primarily based in your settings.
The 2 most typical channel map settings for FPV drones are:
- AETR (Aileron, Elevator, Throttle, Rudder)
- TAER (Throttle, Aileron, Elevator, Rudder)
Every letter represents a selected channel:
- A (Aileron) = Roll (left/proper)
- E (Elevator) = Pitch (ahead/backward)
- T (Throttle) = Throttle (pace up/down)
- R (Rudder) = Yaw (rotate left/proper)
In case your radio’s channel order doesn’t match Betaflight’s setting, your controls will change into blended up—for instance, throttle controlling roll or yaw controlling pitch.
Why is Channel Map Vital?
Chances are you’ll marvel why channel map is required. Nicely, a channel map defines the order of channel outputs (stick instructions). Nevertheless, when these outputs attain the receiver, they’re merely numbers. Your flight controller must be explicitly knowledgeable which quantity corresponds to every command (throttle, pitch, roll, yaw).
Choosing the flawed channel map in Betaflight will lead to incorrect responses to your stick inputs. Your quad might refuse to arm as a result of throttle not being at zero, or if it arms, it may behave unpredictably and uncontrollably.
Default Channel Order in Betaflight
You’ll be able to view or change the channel map in Betaflight Configurator beneath the “Receiver” tab, listed as “Channel Map”.
The default Betaflight channel order is AETR1234:
- CH1: Aileron (Roll)
- CH2: Elevator (Pitch)
- CH3: Throttle
- CH4: Rudder (Yaw)
How one can Repair Fallacious Channel Map
In case your receiver channels are blended up, merely attempt a unique channel map possibility within the Receiver tab of Betaflight Configurator:
- Betaflight default: AETR (AETR1234)
- Various frequent possibility: TAER (listed as “Spektrum / Graupner / JR”)
If not one of the preset choices appropriate the problem, test your transmitter’s channel mixing configuration. Directions are supplied within the subsequent part.
Channel Order in EdgeTX Radio
You’ll be able to view your radio’s channel order on the MIXES web page in any EdgeTX radio.
To keep away from altering Betaflight’s channel map each time you setup a brand new drone, I’d advise to set your radio’s default channel order to match Betaflight’s default (AETR). This includes inserting:
- Aileron (Roll) on Channel 1
- Elevator (Pitch) on Channel 2
- Throttle on Channel 3
- Rudder (Yaw) on Channel 4
Additional Studying: Take a look at this beginner-friendly tutorial on establishing switches within the MIXES web page: https://oscarliang.com/setup-switch-mixes/
You may also wish to verify/set the default Channel Order in EdgeTX – it ensures each new mannequin profile created in your EdgeTX radio will mechanically use the specified channel order:
- Press the SYS button to entry radio settings.
- Navigate to the Settings tab.
- Scroll down and discover Default Channel Order.
- Set it to AETR.
- Press Return to save lots of your adjustments.
How one can Change Channel Order in EdgeTX
To rearrange channel order in your EdgeTX radio, navigate to the MIXES web page in Mannequin Setup, and reorder the primary 4 channels as wanted. For instance, to alter TAER to AETR:
Choose the channel you want to transfer, maintain the Enter button, and click on on “Transfer.”
Transfer THR to CH3 (simply above ELE).
Transfer AIL to CH1, and ELE to CH2.
Affirm that the channel map in Betaflight is now appropriate.
Notice: The order of controls within the INPUTS tab doesn’t matter and might stay unchanged.
Conclusion
Setting your EdgeTX radio’s default channel order to match Betaflight’s (AETR) simplifies your setup course of considerably. With this adjustment, your drones will at all times reply accurately to your controls, permitting you extra time flying and fewer time troubleshooting. Comfortable flying!
Edit Historical past
- 2020 – tutorial created
- Mar 2025 – tutorial up to date